diff options
Diffstat (limited to 'source/n/net-snmp')
| -rw-r--r-- | source/n/net-snmp/doinst.sh | 23 | ||||
| -rwxr-xr-x | source/n/net-snmp/net-snmp.SlackBuild | 145 | ||||
| -rw-r--r-- | source/n/net-snmp/rc.snmpd | 54 | ||||
| -rw-r--r-- | source/n/net-snmp/slack-desc | 19 | ||||
| -rw-r--r-- | source/n/net-snmp/snmpd.conf | 455 |
5 files changed, 696 insertions, 0 deletions
diff --git a/source/n/net-snmp/doinst.sh b/source/n/net-snmp/doinst.sh new file mode 100644 index 000000000..4f1e48303 --- /dev/null +++ b/source/n/net-snmp/doinst.sh @@ -0,0 +1,23 @@ +#!/bin/sh +config() { + NEW="$1" + OLD="`dirname $NEW`/`basename $NEW .new`" + # If there's no config file by that name, mv it over: + if [ ! -r $OLD ]; then + mv $NEW $OLD + elif [ "`cat $OLD | md5sum`" = "`cat $NEW | md5sum`" ]; then # toss the redundant copy + rm $NEW + fi + # Otherwise, we leave the .new copy for the admin to consider... +} + +# Keep same perms on rc.snmpd.new: +if [ -e etc/rc.d/rc.snmpd ]; then + cp -a etc/rc.d/rc.snmpd etc/rc.d/rc.snmpd.new.incoming + cat etc/rc.d/rc.snmpd.new > etc/rc.d/rc.snmpd.new.incoming + mv etc/rc.d/rc.snmpd.new.incoming etc/rc.d/rc.snmpd.new +fi + +config etc/snmp/snmpd.conf.new +config etc/rc.d/rc.snmpd.new + diff --git a/source/n/net-snmp/net-snmp.SlackBuild b/source/n/net-snmp/net-snmp.SlackBuild new file mode 100755 index 000000000..a102b0e56 --- /dev/null +++ b/source/n/net-snmp/net-snmp.SlackBuild @@ -0,0 +1,145 @@ +#!/bin/sh + +# Copyright 2006, 2007, 2008, 2009 Patrick J. Volkerding, Sebeka, MN, USA +# All rights reserved. +# +# Redistribution and use of this script, with or without modification, is +# permitted provided that the following conditions are met: +# +# 1. Redistributions of this script must retain the above copyright +# notice, this list of conditions and the following disclaimer. +# +# THIS SOFTWARE IS PROVIDED BY THE AUTHOR ``AS IS'' AND ANY EXPRESS OR IMPLIED +# WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF +# MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO +# EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, +# SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, +# PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; +# OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, +# WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR +# OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF +# ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + + +PKGNAM=net-snmp +VERSION=${VERSION:-5.4.2.1} +ARCH=${ARCH:-x86_64} +BUILD=${BUILD:-2} + + +CWD=$(pwd) +TMP=${TMP:-/tmp} +PKG=$TMP/package-${PKGNAM} +rm -rf $PKG +mkdir -p $TMP $PKG + +if [ "$ARCH" = "i486" ]; then + SLKCFLAGS="-O2 -march=i486 -mtune=i686" + LIBDIRSUFFIX="" +elif [ "$ARCH" = "s390" ]; then + SLKCFLAGS="-O2" + LIBDIRSUFFIX="" +elif [ "$ARCH" = "x86_64" ]; then + SLKCFLAGS="-O2 -fPIC" + LIBDIRSUFFIX="64" +fi + +cd $TMP +rm -rf ${PKGNAM}-${VERSION} +tar xvf $CWD/${PKGNAM}-$VERSION.tar.bz2 || exit 1 +cd ${PKGNAM}-$VERSION + +# Make sure ownerships and permissions are sane: +chown -R root:root . +find . \ + \( -perm 777 -o -perm 775 -o -perm 711 -o -perm 555 -o -perm 511 \) \ + -exec chmod 755 {} \; -o \ + \( -perm 666 -o -perm 664 -o -perm 600 -o -perm 444 -o -perm 440 -o -perm 400 \) \ + -exec chmod 644 {} \; + +# Configure: +CFLAGS="$SLKCFLAGS" \ +./configure \ + --prefix=/usr \ + --libdir=/usr/lib${LIBDIRSUFFIX} \ + --sysconfdir=/etc/snmp \ + --mandir=/usr/man \ + --enable-ipv6 \ + --disable-debugging \ + --enable-static=no \ + --with-libwrap \ + --with-perl-modules \ + --with-default-snmp-version=3 \ + --with-sys-contact="root@example.org" \ + --with-sys-location="unknown" \ + --with-logfile="/var/log/snmpd.log" \ + --with-persistent-directory="/var/lib/net-snmp" \ + --without-rpm \ + --program-suffix= \ + --program-prefix= \ + --build=$ARCH-slackware-linux + +# Build and install: +# This seems to not play well with "-j N"... +make INSTALLDIRS=vendor || exit 1 +make install INSTALLDIRS=vendor DESTDIR=$PKG || exit 1 + +# Evidently --mandir=/usr/man doesn't catch everything... +if [ -d $PKG/usr/share/man/man3 ]; then + mkdir -p $PKG/usr/man/man3 + mv $PKG/usr/share/man/man3/* $PKG/usr/man/man3 + rmdir $PKG/usr/share/man/man3 $PKG/usr/share/man +fi +mkdir -p $PKG/usr +mv $PKG/usr/share/man $PKG/usr + +mkdir -p $PKG/var/lib/net-snmp +mkdir -p $PKG/etc/snmp +zcat $CWD/snmpd.conf.gz > $PKG/etc/snmp/snmpd.conf.new +mkdir -p $PKG/etc/rc.d +cat $CWD/rc.snmpd > $PKG/etc/rc.d/rc.snmpd.new + +# Strip binaries: +find $PKG | xargs file | grep -e "executable" -e "shared object" | grep ELF \ + | cut -f 1 -d : | xargs strip --strip-unneeded 2> /dev/null + +# Compress and link manpages, if any: +if [ -d $PKG/usr/man ]; then + ( cd $PKG/usr/man + for manpagedir in $(find . -type d -name "man*") ; do + ( cd $manpagedir + for eachpage in $( find . -type l -maxdepth 1) ; do + ln -s $( readlink $eachpage ).gz $eachpage.gz + rm $eachpage + done + gzip -9 *.* + ) + done + ) +fi + +# Compress info files, if any: +if [ -d $PKG/usr/info ]; then + ( cd $PKG/usr/info + rm -f dir + gzip -9 * + ) +fi + +# Remove perllocal files: +( cd $PKG ; find . -name perllocal.pod -exec rm "{}" \; ) + +# Add a documentation directory: +mkdir -p $PKG/usr/doc/${PKGNAM}-$VERSION +cp -a \ + AGENT.txt CHANGES COPYING* CodingStyle EXAMPLE* FAQ \ + INSTALL NEWS PORTING README* TODO \ + $PKG/usr/doc/${PKGNAM}-$VERSION + +mkdir -p $PKG/install +zcat $CWD/doinst.sh.gz > $PKG/install/doinst.sh +cat $CWD/slack-desc > $PKG/install/slack-desc + +cd $PKG +/sbin/makepkg -l y -c n $TMP/${PKGNAM}-$VERSION-$ARCH-$BUILD.txz + diff --git a/source/n/net-snmp/rc.snmpd b/source/n/net-snmp/rc.snmpd new file mode 100644 index 000000000..cd52366c6 --- /dev/null +++ b/source/n/net-snmp/rc.snmpd @@ -0,0 +1,54 @@ +#!/bin/sh +# +# rc.snmpd This shell script takes care of starting and stopping +# the net-snmp SNMP daemon + +OPTIONS="-A -p /var/run/snmpd -a" + +start() { + if [ -x /usr/sbin/snmpd -a -f /etc/snmp/snmpd.conf ]; then + echo -n "Starting snmpd: " + /usr/sbin/snmpd $OPTIONS -c /etc/snmp/snmpd.conf + echo " /usr/sbin/snmpd $OPTIONS -c /etc/snmp/snmpd.conf" + fi +} + +stop() { + # Stop daemons. + COUNT=0 + echo -n "Shutting down snmpd: " + while `killall snmpd 2>/dev/null`; do + echo -n "." + sleep 1 + COUNT=$((COUNT+1)) + if [ $COUNT -ge 30 ]; then + killall -9 snmpd + sleep 1 + break + fi + done + echo " DONE" +} + +# See how we were called. +case "$1" in + start) + start + ;; + stop) + stop + ;; + restart|reload) + stop + start + ;; + condrestart) + if [ -f /var/run/snmpd ]; then + stop + start + fi + ;; + *) + echo $"Usage: $0 {start|stop|restart|condrestart}" + ;; +esac diff --git a/source/n/net-snmp/slack-desc b/source/n/net-snmp/slack-desc new file mode 100644 index 000000000..7659f7fc8 --- /dev/null +++ b/source/n/net-snmp/slack-desc @@ -0,0 +1,19 @@ +# HOW TO EDIT THIS FILE: +# The "handy ruler" below makes it easier to edit a package description. Line +# up the first '|' above the ':' following the base package name, and the '|' +# on the right side marks the last column you can put a character in. You must +# make exactly 11 lines for the formatting to be correct. It's also +# customary to leave one space after the ':'. + + |-----handy-ruler------------------------------------------------------| +net-snmp: net-snmp (Simple Network Management Protocol tools) +net-snmp: +net-snmp: Various tools relating to the Simple Network Management Protocol: +net-snmp: +net-snmp: An extensible agent +net-snmp: An SNMP library +net-snmp: Tools to request or set information from SNMP agents +net-snmp: Tools to generate and handle SNMP traps +net-snmp: A version of the unix 'netstat' command using SNMP +net-snmp: A graphical Perl/Tk/SNMP based mib browser +net-snmp: diff --git a/source/n/net-snmp/snmpd.conf b/source/n/net-snmp/snmpd.conf new file mode 100644 index 000000000..51dce4edb --- /dev/null +++ b/source/n/net-snmp/snmpd.conf @@ -0,0 +1,455 @@ +############################################################################### +# +# snmpd.conf: +# An example configuration file for configuring the ucd-snmp snmpd agent. +# +############################################################################### +# +# This file is intended to only be as a starting point. Many more +# configuration directives exist than are mentioned in this file. For +# full details, see the snmpd.conf(5) manual page. +# +# All lines beginning with a '#' are comments and are intended for you +# to read. All other lines are configuration commands for the agent. + +############################################################################### +# Access Control +############################################################################### + +# As shipped, the snmpd demon will only respond to queries on the +# system mib group until this file is replaced or modified for +# security purposes. Examples are shown below about how to increase the +# level of access. + +# By far, the most common question I get about the agent is "why won't +# it work?", when really it should be "how do I configure the agent to +# allow me to access it?" +# +# By default, the agent responds to the "public" community for read +# only access, if run out of the box without any configuration file in +# place. The following examples show you other ways of configuring +# the agent so that you can change the community names, and give +# yourself write access to the mib tree as well. +# +# For more information, read the FAQ as well as the snmpd.conf(5) +# manual page. + +#### +# First, map the community name "public" into a "security name" + +# sec.name source community +com2sec notConfigUser default public + +#### +# Second, map the security name into a group name: + +# groupName securityModel securityName +group notConfigGroup v1 notConfigUser +group notConfigGroup v2c notConfigUser + +#### +# Third, create a view for us to let the group have rights to: + +# Make at least snmpwalk -v 1 localhost -c public system fast again. +# name incl/excl subtree mask(optional) +view systemview included .1.3.6.1.2.1.1 +view systemview included .1.3.6.1.2.1.25.1.1 + +#### +# Finally, grant the group read-only access to the systemview view. + +# group context sec.model sec.level prefix read write notif +access notConfigGroup "" any noauth exact systemview none none + +# ----------------------------------------------------------------------------- + +# Here is a commented out example configuration that allows less +# restrictive access. + +# YOU SHOULD CHANGE THE "COMMUNITY" TOKEN BELOW TO A NEW KEYWORD ONLY +# KNOWN AT YOUR SITE. YOU *MUST* CHANGE THE NETWORK TOKEN BELOW TO +# SOMETHING REFLECTING YOUR LOCAL NETWORK ADDRESS SPACE. + +## sec.name source community +#com2sec local localhost COMMUNITY +#com2sec mynetwork NETWORK/24 COMMUNITY + +## group.name sec.model sec.name +#group MyRWGroup any local +#group MyROGroup any mynetwork +# +#group MyRWGroup any otherv3user +#... + +## incl/excl subtree mask +#view all included .1 80 + +## -or just the mib2 tree- + +#view mib2 included .iso.org.dod.internet.mgmt.mib-2 fc + + +## context sec.model sec.level prefix read write notif +#access MyROGroup "" any noauth 0 all none none +#access MyRWGroup "" any noauth 0 all all all + + +############################################################################### +# Sample configuration to make net-snmpd RFC 1213. +# Unfortunately v1 and v2c don't allow any user based authentification, so +# opening up the default config is not an option from a security point. +# +# WARNING: If you uncomment the following lines you allow write access to your +# snmpd daemon from any source! To avoid this use different names for your +# community or split out the write access to a different community and +# restrict it to your local network. +# Also remember to comment the syslocation and syscontact parameters later as +# otherwise they are still read only (see FAQ for net-snmp). +# + +# First, map the community name "public" into a "security name" +# sec.name source community +#com2sec notConfigUser default public + +# Second, map the security name into a group name: +# groupName securityModel securityName +#group notConfigGroup v1 notConfigUser +#group notConfigGroup v2c notConfigUser + +# Third, create a view for us to let the group have rights to: +# Open up the whole tree for ro, make the RFC 1213 required ones rw. +# name incl/excl subtree mask(optional) +#view roview included .1 +#view rwview included system.sysContact +#view rwview included system.sysName +#view rwview included system.sysLocation +#view rwview included interfaces.ifTable.ifEntry.ifAdminStatus +#view rwview included at.atTable.atEntry.atPhysAddress +#view rwview included at.atTable.atEntry.atNetAddress +#view rwview included ip.ipForwarding +#view rwview included ip.ipDefaultTTL +#view rwview included ip.ipRouteTable.ipRouteEntry.ipRouteDest +#view rwview included ip.ipRouteTable.ipRouteEntry.ipRouteIfIndex +#view rwview included ip.ipRouteTable.ipRouteEntry.ipRouteMetric1 +#view rwview included ip.ipRouteTable.ipRouteEntry.ipRouteMetric2 +#view rwview included ip.ipRouteTable.ipRouteEntry.ipRouteMetric3 +#view rwview included ip.ipRouteTable.ipRouteEntry.ipRouteMetric4 +#view rwview included ip.ipRouteTable.ipRouteEntry.ipRouteType +#view rwview included ip.ipRouteTable.ipRouteEntry.ipRouteAge +#view rwview included ip.ipRouteTable.ipRouteEntry.ipRouteMask +#view rwview included ip.ipRouteTable.ipRouteEntry.ipRouteMetric5 +#view rwview included ip.ipNetToMediaTable.ipNetToMediaEntry.ipNetToMediaIfIndex +#view rwview included ip.ipNetToMediaTable.ipNetToMediaEntry.ipNetToMediaPhysAddress +#view rwview included ip.ipNetToMediaTable.ipNetToMediaEntry.ipNetToMediaNetAddress +#view rwview included ip.ipNetToMediaTable.ipNetToMediaEntry.ipNetToMediaType +#view rwview included tcp.tcpConnTable.tcpConnEntry.tcpConnState +#view rwview included egp.egpNeighTable.egpNeighEntry.egpNeighEventTrigger +#view rwview included snmp.snmpEnableAuthenTraps + +# Finally, grant the group read-only access to the systemview view. +# group context sec.model sec.level prefix read write notif +#access notConfigGroup "" any noauth exact roview rwview none + + + +############################################################################### +# System contact information +# + +# It is also possible to set the sysContact and sysLocation system +# variables through the snmpd.conf file: + +syslocation Unknown (edit /etc/snmp/snmpd.conf) +syscontact Root <root@localhost> (configure /etc/snmp/snmp.local.conf) + +# Example output of snmpwalk: +# % snmpwalk -v 1 localhost -c public system +# system.sysDescr.0 = "SunOS name sun4c" +# system.sysObjectID.0 = OID: enterprises.ucdavis.ucdSnmpAgent.sunos4 +# system.sysUpTime.0 = Timeticks: (595637548) 68 days, 22:32:55 +# system.sysContact.0 = "Me <me@somewhere.org>" +# system.sysName.0 = "name" +# system.sysLocation.0 = "Right here, right now." +# system.sysServices.0 = 72 + + +# ----------------------------------------------------------------------------- + + +############################################################################### +# Process checks. +# +# The following are examples of how to use the agent to check for +# processes running on the host. The syntax looks something like: +# +# proc NAME [MAX=0] [MIN=0] +# +# NAME: the name of the process to check for. It must match +# exactly (ie, http will not find httpd processes). +# MAX: the maximum number allowed to be running. Defaults to 0. +# MIN: the minimum number to be running. Defaults to 0. + +# +# Examples (commented out by default): +# + +# Make sure mountd is running +#proc mountd + +# Make sure there are no more than 4 ntalkds running, but 0 is ok too. +#proc ntalkd 4 + +# Make sure at least one sendmail, but less than or equal to 10 are running. +#proc sendmail 10 1 + +# A snmpwalk of the process mib tree would look something like this: +# +# % snmpwalk -v 1 localhost -c public .1.3.6.1.4.1.2021.2 +# enterprises.ucdavis.procTable.prEntry.prIndex.1 = 1 +# enterprises.ucdavis.procTable.prEntry.prIndex.2 = 2 +# enterprises.ucdavis.procTable.prEntry.prIndex.3 = 3 +# enterprises.ucdavis.procTable.prEntry.prNames.1 = "mountd" +# enterprises.ucdavis.procTable.prEntry.prNames.2 = "ntalkd" +# enterprises.ucdavis.procTable.prEntry.prNames.3 = "sendmail" +# enterprises.ucdavis.procTable.prEntry.prMin.1 = 0 +# enterprises.ucdavis.procTable.prEntry.prMin.2 = 0 +# enterprises.ucdavis.procTable.prEntry.prMin.3 = 1 +# enterprises.ucdavis.procTable.prEntry.prMax.1 = 0 +# enterprises.ucdavis.procTable.prEntry.prMax.2 = 4 +# enterprises.ucdavis.procTable.prEntry.prMax.3 = 10 +# enterprises.ucdavis.procTable.prEntry.prCount.1 = 0 +# enterprises.ucdavis.procTable.prEntry.prCount.2 = 0 +# enterprises.ucdavis.procTable.prEntry.prCount.3 = 1 +# enterprises.ucdavis.procTable.prEntry.prErrorFlag.1 = 1 +# enterprises.ucdavis.procTable.prEntry.prErrorFlag.2 = 0 +# enterprises.ucdavis.procTable.prEntry.prErrorFlag.3 = 0 +# enterprises.ucdavis.procTable.prEntry.prErrMessage.1 = "No mountd process running." +# enterprises.ucdavis.procTable.prEntry.prErrMessage.2 = "" +# enterprises.ucdavis.procTable.prEntry.prErrMessage.3 = "" +# enterprises.ucdavis.procTable.prEntry.prErrFix.1 = 0 +# enterprises.ucdavis.procTable.prEntry.prErrFix.2 = 0 +# enterprises.ucdavis.procTable.prEntry.prErrFix.3 = 0 +# +# Note that the errorFlag for mountd is set to 1 because one is not +# running (in this case an rpc.mountd is, but thats not good enough), +# and the ErrMessage tells you what's wrong. The configuration +# imposed in the snmpd.conf file is also shown. +# +# Special Case: When the min and max numbers are both 0, it assumes +# you want a max of infinity and a min of 1. +# + + +# ----------------------------------------------------------------------------- + + +############################################################################### +# Executables/scripts +# + +# +# You can also have programs run by the agent that return a single +# line of output and an exit code. Here are two examples. +# +# exec NAME PROGRAM [ARGS ...] +# +# NAME: A generic name. +# PROGRAM: The program to run. Include the path! +# ARGS: optional arguments to be passed to the program + +# a simple hello world + +#exec echotest /bin/echo hello world + +# Run a shell script containing: +# +# #!/bin/sh +# echo hello world +# echo hi there +# exit 35 +# +# Note: this has been specifically commented out to prevent +# accidental security holes due to someone else on your system writing +# a /tmp/shtest before you do. Uncomment to use it. +# +#exec shelltest /bin/sh /tmp/shtest + +# Then, +# % snmpwalk -v 1 localhost -c public .1.3.6.1.4.1.2021.8 +# enterprises.ucdavis.extTable.extEntry.extIndex.1 = 1 +# enterprises.ucdavis.extTable.extEntry.extIndex.2 = 2 +# enterprises.ucdavis.extTable.extEntry.extNames.1 = "echotest" +# enterprises.ucdavis.extTable.extEntry.extNames.2 = "shelltest" +# enterprises.ucdavis.extTable.extEntry.extCommand.1 = "/bin/echo hello world" +# enterprises.ucdavis.extTable.extEntry.extCommand.2 = "/bin/sh /tmp/shtest" +# enterprises.ucdavis.extTable.extEntry.extResult.1 = 0 +# enterprises.ucdavis.extTable.extEntry.extResult.2 = 35 +# enterprises.ucdavis.extTable.extEntry.extOutput.1 = "hello world." +# enterprises.ucdavis.extTable.extEntry.extOutput.2 = "hello world." +# enterprises.ucdavis.extTable.extEntry.extErrFix.1 = 0 +# enterprises.ucdavis.extTable.extEntry.extErrFix.2 = 0 + +# Note that the second line of the /tmp/shtest shell script is cut +# off. Also note that the exit status of 35 was returned. + +# ----------------------------------------------------------------------------- + + +############################################################################### +# disk checks +# + +# The agent can check the amount of available disk space, and make +# sure it is above a set limit. + +# disk PATH [MIN=100000] +# +# PATH: mount path to the disk in question. +# MIN: Disks with space below this value will have the Mib's errorFlag set. +# Default value = 100000. + +# Check the / partition and make sure it contains at least 10 megs. + +#disk / 10000 + +# % snmpwalk -v 1 localhost -c public .1.3.6.1.4.1.2021.9 +# enterprises.ucdavis.diskTable.dskEntry.diskIndex.1 = 0 +# enterprises.ucdavis.diskTable.dskEntry.diskPath.1 = "/" Hex: 2F +# enterprises.ucdavis.diskTable.dskEntry.diskDevice.1 = "/dev/dsk/c201d6s0" +# enterprises.ucdavis.diskTable.dskEntry.diskMinimum.1 = 10000 +# enterprises.ucdavis.diskTable.dskEntry.diskTotal.1 = 837130 +# enterprises.ucdavis.diskTable.dskEntry.diskAvail.1 = 316325 +# enterprises.ucdavis.diskTable.dskEntry.diskUsed.1 = 437092 +# enterprises.ucdavis.diskTable.dskEntry.diskPercent.1 = 58 +# enterprises.ucdavis.diskTable.dskEntry.diskErrorFlag.1 = 0 +# enterprises.ucdavis.diskTable.dskEntry.diskErrorMsg.1 = "" + +# ----------------------------------------------------------------------------- + + +############################################################################### +# load average checks +# + +# load [1MAX=12.0] [5MAX=12.0] [15MAX=12.0] +# +# 1MAX: If the 1 minute load average is above this limit at query +# time, the errorFlag will be set. +# 5MAX: Similar, but for 5 min average. +# 15MAX: Similar, but for 15 min average. + +# Check for loads: +#load 12 14 14 + +# % snmpwalk -v 1 localhost -c public .1.3.6.1.4.1.2021.10 +# enterprises.ucdavis.loadTable.laEntry.loadaveIndex.1 = 1 +# enterprises.ucdavis.loadTable.laEntry.loadaveIndex.2 = 2 +# enterprises.ucdavis.loadTable.laEntry.loadaveIndex.3 = 3 +# enterprises.ucdavis.loadTable.laEntry.loadaveNames.1 = "Load-1" +# enterprises.ucdavis.loadTable.laEntry.loadaveNames.2 = "Load-5" +# enterprises.ucdavis.loadTable.laEntry.loadaveNames.3 = "Load-15" +# enterprises.ucdavis.loadTable.laEntry.loadaveLoad.1 = "0.49" Hex: 30 2E 34 39 +# enterprises.ucdavis.loadTable.laEntry.loadaveLoad.2 = "0.31" Hex: 30 2E 33 31 +# enterprises.ucdavis.loadTable.laEntry.loadaveLoad.3 = "0.26" Hex: 30 2E 32 36 +# enterprises.ucdavis.loadTable.laEntry.loadaveConfig.1 = "12.00" +# enterprises.ucdavis.loadTable.laEntry.loadaveConfig.2 = "14.00" +# enterprises.ucdavis.loadTable.laEntry.loadaveConfig.3 = "14.00" +# enterprises.ucdavis.loadTable.laEntry.loadaveErrorFlag.1 = 0 +# enterprises.ucdavis.loadTable.laEntry.loadaveErrorFlag.2 = 0 +# enterprises.ucdavis.loadTable.laEntry.loadaveErrorFlag.3 = 0 +# enterprises.ucdavis.loadTable.laEntry.loadaveErrMessage.1 = "" +# enterprises.ucdavis.loadTable.laEntry.loadaveErrMessage.2 = "" +# enterprises.ucdavis.loadTable.laEntry.loadaveErrMessage.3 = "" + +# ----------------------------------------------------------------------------- + + +############################################################################### +# Extensible sections. +# + +# This alleviates the multiple line output problem found in the +# previous executable mib by placing each mib in its own mib table: + +# Run a shell script containing: +# +# #!/bin/sh +# echo hello world +# echo hi there +# exit 35 +# +# Note: this has been specifically commented out to prevent +# accidental security holes due to someone else on your system writing +# a /tmp/shtest before you do. Uncomment to use it. +# +# exec .1.3.6.1.4.1.2021.50 shelltest /bin/sh /tmp/shtest + +# % snmpwalk -v 1 localhost -c public .1.3.6.1.4.1.2021.50 +# enterprises.ucdavis.50.1.1 = 1 +# enterprises.ucdavis.50.2.1 = "shelltest" +# enterprises.ucdavis.50.3.1 = "/bin/sh /tmp/shtest" +# enterprises.ucdavis.50.100.1 = 35 +# enterprises.ucdavis.50.101.1 = "hello world." +# enterprises.ucdavis.50.101.2 = "hi there." +# enterprises.ucdavis.50.102.1 = 0 + +# Now the Output has grown to two lines, and we can see the 'hi +# there.' output as the second line from our shell script. +# +# Note that you must alter the mib.txt file to be correct if you want +# the .50.* outputs above to change to reasonable text descriptions. + +# Other ideas: +# +# exec .1.3.6.1.4.1.2021.51 ps /bin/ps +# exec .1.3.6.1.4.1.2021.52 top /usr/local/bin/top +# exec .1.3.6.1.4.1.2021.53 mailq /usr/bin/mailq + +# ----------------------------------------------------------------------------- + + +############################################################################### +# Pass through control. +# + +# Usage: +# pass MIBOID EXEC-COMMAND +# +# This will pass total control of the mib underneath the MIBOID +# portion of the mib to the EXEC-COMMAND. +# +# Note: You'll have to change the path of the passtest script to your +# source directory or install it in the given location. +# +# Example: (see the script for details) +# (commented out here since it requires that you place the +# script in the right location. (its not installed by default)) + +# pass .1.3.6.1.4.1.2021.255 /bin/sh /usr/local/local/passtest + +# % snmpwalk -v 1 localhost -c public .1.3.6.1.4.1.2021.255 +# enterprises.ucdavis.255.1 = "life the universe and everything" +# enterprises.ucdavis.255.2.1 = 42 +# enterprises.ucdavis.255.2.2 = OID: 42.42.42 +# enterprises.ucdavis.255.3 = Timeticks: (363136200) 42 days, 0:42:42 +# enterprises.ucdavis.255.4 = IpAddress: 127.0.0.1 +# enterprises.ucdavis.255.5 = 42 +# enterprises.ucdavis.255.6 = Gauge: 42 +# +# % snmpget -v 1 localhost public .1.3.6.1.4.1.2021.255.5 +# enterprises.ucdavis.255.5 = 42 +# +# % snmpset -v 1 localhost public .1.3.6.1.4.1.2021.255.1 s "New string" +# enterprises.ucdavis.255.1 = "New string" +# + +# For specific usage information, see the man/snmpd.conf.5 manual page +# as well as the local/passtest script used in the above example. + +# Added for support of bcm5820 cards. +pass .1.3.6.1.4.1.4413.4.1 /usr/bin/ucd5820stat + +############################################################################### +# Further Information +# +# See the snmpd.conf manual page, and the output of "snmpd -H". |