# /etc/rc.d/rc.inet1.conf
#
# This file contains the configuration settings for network interfaces.
#
# If USE_DHCP[interface] is set to "yes", this overrides any other settings.
# If you don't have an interface, leave the settings null ("").
#
# You can configure network interfaces other than eth0,eth1... by setting
# IFNAME[interface] to the interface's name. If IFNAME[interface] is unset
# or empty, it is assumed you're configuring eth<interface>.
#
# Several other parameters are available; the end of this file contains a
# comprehensive set of examples.
#
# Important note for IPv6 stateless auto configuration (SLAAC) users:
# From Slackware 15.0 onwards, you need to set USE_SLAAC[0]="yes" below.
# =============================================================================
# IPv4 config options for eth0:
IPADDRS[0]=""
USE_DHCP[0]=""
# IPv6 config options for eth0:
IP6ADDRS[0]=""
USE_SLAAC[0]=""
USE_DHCP6[0]=""
# Generic options for eth0:
DHCP_HOSTNAME[0]=""
# IPv4 config options for eth1:
IPADDRS[1]=""
USE_DHCP[1]=""
# IPv6 config options for eth1:
IP6ADDRS[1]=""
USE_SLAAC[1]=""
USE_DHCP6[1]=""
# Generic options for eth1:
DHCP_HOSTNAME[1]=""
# IPv4 config options for eth2:
IPADDRS[2]=""
USE_DHCP[2]=""
# IPv6 config options for eth2:
IP6ADDRS[2]=""
USE_SLAAC[2]=""
USE_DHCP6[2]=""
# Generic options for eth2:
DHCP_HOSTNAME[2]=""
# IPv4 config options for eth3:
IPADDRS[3]=""
USE_DHCP[3]=""
# IPv6 config options for eth3:
IP6ADDRS[3]=""
USE_SLAAC[3]=""
USE_DHCP6[3]=""
# Generic options for eth3:
DHCP_HOSTNAME[3]=""
# IPv4 default gateway IP address:
GATEWAY=""
# IPv6 default gateway IP address:
GATEWAY6=""
# =============================================================================
# Example of how to configure a bond (link aggregation) interface.
# Note the addition of the BONDNICS and BONDMODE parameters.
# BONDNICS is a space delimited list of interfaces to add to this bond. The
# BONDNICS interfaces will be brought up and configured while bringing up the
# bond interface, so do not need to be previously defined in rc.inet1.conf.
# BONDMODE sets the bonding mode for this interface. If not specified when
# BONDNICS has been used, the default is 'balance-rr'.
# IFOPTS is a pipe (|) delimited list of bonding module specific settings to be
# applied to the interface, and should always include the 'miimon' option when
# configuring bonding - not using this option will result in network
# degradation. In 'active-backup' mode, the 'primary' option should also be
# supplied. When using '802.3ad' mode, set "lacp_rate fast" for faster
# recovery from an interface failure. In other modes, the 'xmit_hash_policy'
# should be set. See the /usr/src/linux/Documentation/networking/bonding.txt
# file (search for "Bonding Driver Options") for the full set of options.
#IFNAME[0]="bond0"
#BONDNICS[0]="eth0 eth1"
#BONDMODE[0]="balance-rr"
#IFOPTS[0]="xmit_hash_policy layer2+3 | miimon 100"
#IPADDRS[0]="192.168.0.1/24"
#USE_DHCP[0]=""
#DHCP_HOSTNAME[0]=""
#IP6ADDRS[0]=""
#USE_SLAAC[0]=""
#USE_DHCP6[0]=""
# =============================================================================
# Example of how to configure a VLAN interface:
# The VLAN ID is taken from the full interface name, which is comprised of the
# underlying interface name, a period (.) and then the VLAN ID.
# IFOPTS is a pipe (|) delimited list of VLAN module specific settings to be
# applied to the interface. See the ip-link(8) man page (search for "VLAN Type
# Support") for details of the options available. This option is not required
# for a standard VLAN to be configured.
#IFNAME[0]="eth0.10"
#IFOPTS[0]=""
#IPADDRS[0]="192.168.10.1/24"
#USE_DHCP[0]=""
#DHCP_HOSTNAME[0]=""
#IP6ADDRS[0]=""
#USE_SLAAC[0]=""
#USE_DHCP6[0]=""
# =============================================================================
# Example of how to configure a bridge:
# Note the added "BRNICS" variable which contains a space-separated list
# of the physical or virtual network interfaces you want to add to the bridge.
# IFOPTS is a pipe (|) delimited list of bridge module specific settings to be
# applied to the interface. See the ip-link(8) man page (search for "BRIDGE
# Type Support") for details of the options available. This option is not
# required for a standard bridge to be configured.
#IFNAME[0]="br0"
#BRNICS[0]="eth0"
#IFOPTS[0]=""
#IPADDRS[0]="192.168.0.1/24"
#USE_DHCP[0]=""
#DHCP_HOSTNAME[0]=""
# =============================================================================
# Virtual interfaces to create - these are created before any address
# configuration or bridge setup is done, so you may use these interfaces
# as IFNAME or BRNICS values. These can be tun or tap interfaces:
# adjust VIRTIFNAME and VIRTIFTYPE accordingly.
# Starting with VIRTIFNAME[0] is mandatory, and each next one must be
# incremented by one, so VIRTIFNAME[1], VIRTIFNAME[2], and so on.
# Virtual tap interface example
#VIRTIFNAME[0]="tap0"
#VIRTIFTYPE[0]="tap"
#VIRTIFUSER[0]="root"
#VIRTIFGROUP[0]="root"
# Virtual tun interface example
#VIRTIFNAME[1]="tun0"
#VIRTIFTYPE[1]="tun"
#VIRTIFUSER[1]="someuser"
#VIRTIFGROUP[1]="somegroup"
# =============================================================================
# Example config information for wlan0:
# Uncomment the lines you need and fill in your data. You may not need all of
# these for your wireless network.
#IFNAME[4]="wlan0"
#IPADDRS[4]=""
#USE_DHCP[4]="yes"
#DHCP_HOSTNAME[4]="icculus-wireless"
#DHCP_KEEPRESOLV[4]="yes"
#DHCP_KEEPNTP[4]="yes"
#DHCP_KEEPGW[4]="yes"
#DHCP_IPADDR[4]=""
#WLAN_ESSID[4]=DARKSTAR
#WLAN_MODE[4]=Managed
#WLAN_RATE[4]="54M auto"
#WLAN_CHANNEL[4]="auto"
#WLAN_KEY[4]="D5A31F54ACF0487C2D0B1C10D2"
#WLAN_IWPRIV[4]="set AuthMode=WPAPSK | set EncrypType=TKIP | set WPAPSK=96389dc66eaf7e6efd5b5523ae43c7925ff4df2f8b7099495192d44a774fda16"
#WLAN_WPA[4]="wpa_supplicant"
#WLAN_WPADRIVER[4]="wext"
#WLAN_WPAWAIT[4]=30
# =============================================================================
# Some examples of additional network parameters that you can use.
#IFNAME[4]="wlan0" # Use a different interface name instead of
# the default 'eth4'
#IFOPTS[4]="" # A pipe (|) delimited list of interface type
# specific options to apply. These options
# can be found in the ip-link(8) man page in
# the approprite section for the interface
# type being configured.
#HWADDR[4]="00:01:23:45:67:89" # Overrule the card's hardware MAC address
#MTU[4]="" # The default MTU is 1500, but you might need
# 1360 when you use NAT'ed IPSec traffic.
#PROMISCUOUS[4]="yes" # Set promiscuous mode on the interface.
#DHCP_TIMEOUT[4]="15" # The default timeout for the DHCP client to
# wait for server resonse is 15 seconds, but
# you might want a shorter or longer wait.
#DHCP_KEEPRESOLV[4]="yes" # If you don't want /etc/resolv.conf overwritten
#DHCP_KEEPNTP[4]="yes" # If you don't want ntp.conf overwritten
#DHCP_KEEPGW[4]="yes" # If you don't want the DHCP server to change
# your default gateway
#DHCP_IPADDR[4]="" # Request a specific IP address from the DHCP
# server
#DHCP_DEBUG[4]="yes" # Make dhcpcd show verbose diagnostics
#DHCP_NOIPV4LL[4]="yes" # Do not assign an ipv4ll address when a DHCP
# server is not found (ipv4ll link-local
# adresses in the IP range 169.254.0.0/16 are
# also known as "zeroconf" addresses)
#SLAAC_TIMEOUT[4]="15" # The default timeout for auto configuration to
# wait for the interface to come up is 15 sec.
# Increase the timeout if required.
#SLAAC_PRIVIPGEN[4]="yes" # When assigning addresses via SLAAC, use the
# 'private' (RFC7217) address generation method.
# It is advisable to also set SLAAC_SECRET[x].
#SLAAC_SECRET[4]="xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx"
# When SLAAC_PRIVIPGEN[x]="yes" is set, this is
# the secret to be used. This must be in the
# form of an IPv6 address. When left unset, a
# random secret is used (this is the default).
#SLAAC_TEMPADDR[4]="yes" # Use a temporary address with SLAAC to enhance
# security.
#USE_RA[4]="yes" # Accept router advertisements even when SLAAC
# is disabled on the interface.
#WLAN_ESSID[4]="DARKSTAR" # An example of how you can override _any_
# parameter defined in rc.wireless.conf, by
# prepending 'WLAN_' to the parameter's name.
# Useful with multiple wireless interfaces.
#WLAN_IWPRIV[4]="set AuthMode=WPAPSK | set EncrypType=TKIP | set WPAPSK=thekey"
# Some drivers require a private ioctl to be
# set through the iwpriv command. If more than
# one is required, you can place them in the
# IWPRIV parameter (separated with the pipe (|)
# character, see the example).
#WLAN_WPA[4]="wpa_supplicant" # Run wpa_supplicant for WPA support
#WLAN_WPADRIVER[4]="ndiswrapper"# Tell wpa_supplicant to specifically use the
# ndiswrapper driver (if you leave this empty
# the 'wext' driver is used by default)
#WLAN_WPAWAIT[4]="30" # In case it takes long for the WPA association
# to finish, you can increase the wait time
# (defaults to 10 seconds)
# =============================================================================
# Change this to "yes" for debugging output to syslog (if available, stdout if
# not).
DEBUG_ETH_UP="no"
# MAXNICS is the maximum number of interfaces that will be configured.
# You may need to increase the MAXNICS value if you have many interfaces, or
# you use multiple VLANs and/or bridges. The default is 6.
#MAXNICS="6"
