path: root/patches/source/ppp/options.new

# /etc/ppp/options
# 
# $Id: options,v 1.4 1996/05/01 18:57:04 alvar Exp $
# 
# Originally created by Jim Knoble <jmknoble@mercury.interpath.net>
# Modified for Debian by alvar Bray <alvar@meiko.co.uk>
# Modified for PPP Server setup by Christoph Lameter <clameter@debian.org>
# Modified for Slackware by Pat Volkerding <volkerdi@slackware.com>
#
# Use the command  egrep -v '#|^ *$' /etc/ppp/options to quickly see what 
# options are active in this file.

# Specify which DNS Servers the incoming Win95 or WinNT Connection should use
# Two Servers can be remotely configured
# dns-addr 192.168.1.1
# dns-addr 192.168.1.2

# Specify which WINS Servers the incoming connection Win95 or WinNT should use
# wins-addr 192.168.1.50
# wins-addr 192.168.1.51

# Run the executable or shell command specified after pppd has
# terminated the link.  This script could, for example, issue commands
# to the modem to cause it to hang up if hardware modem control signals
# were not available.
#disconnect "chat -- \d+++\d\c OK ath0 OK"

# async character map -- 32-bit hex; each bit is a character
# that needs to be escaped for pppd to receive it.  0x00000001
# represents '\x01', and 0x80000000 represents '\x1f'.
asyncmap 0

# Require the peer to authenticate itself before allowing network
# packets to be sent or received.
# For a PPP Server with script based logins not using PAP or CHAP
# you need to disable this setting.
#auth

# Do not require the other end of the connection to authenticate itself.
# This option is dangerous if pppd is setuid.
# If you also have ethernet and are having problems getting PPP to connect
# over a modem, try this option.
#noauth

# Use hardware flow control (i.e. RTS/CTS) to control the flow of data
# on the serial port.
crtscts

# Use software flow control (i.e. XON/XOFF) to control the flow of data
# on the serial port.
#xonxoff

# Specifies that certain characters should be escaped on transmission
# (regardless of whether the peer requests them to be escaped with its
# async control character map).  The characters to be escaped are
# specified as a list of hex numbers separated by commas.  Note that
# almost any character can be specified for the escape option, unlike
# the asyncmap option which only allows control characters to be
# specified.  The characters which may not be escaped are those with hex
# values 0x20 - 0x3f or 0x5e.
#escape 11,13,ff

# Don't use the modem control lines.
#local

# Specifies that pppd should use a UUCP-style lock on the serial device
# to ensure exclusive access to the device.
lock

# Use the modem control lines.  On Ultrix, this option implies hardware
# flow control, as for the crtscts option.  (This option is not fully
# implemented.)
modem

# Set the MRU [Maximum Receive Unit] value to <n> for negotiation.  pppd
# will ask the peer to send packets of no more than <n> bytes. The
# minimum MRU value is 128.  The default MRU value is 1500.  A value of
# 296 is recommended for slow links (40 bytes for TCP/IP header + 256
# bytes of data).
#mru 542

# Set the interface netmask to <n>, a 32 bit netmask in "decimal dot"
# notation (e.g. 255.255.255.0).
#netmask 255.255.255.0

# Disables the default behaviour when no local IP address is specified,
# which is to determine (if possible) the local IP address from the
# hostname. With this option, the peer will have to supply the local IP
# address during IPCP negotiation (unless it specified explicitly on the
# command line or in an options file).
#noipdefault

# Enables the "passive" option in the LCP.  With this option, pppd will
# attempt to initiate a connection; if no reply is received from the
# peer, pppd will then just wait passively for a valid LCP packet from
# the peer (instead of exiting, as it does without this option).
#passive

# With this option, pppd will not transmit LCP packets to initiate a
# connection until a valid LCP packet is received from the peer (as for
# the "passive" option with old versions of pppd).
#silent

# Don't request or allow negotiation of any options for LCP and IPCP
# (use default values).
#-all

# Disable Address/Control compression negotiation (use default, i.e.
# address/control field disabled).
#-ac

# Disable asyncmap negotiation (use the default asyncmap, i.e. escape
# all control characters).
#-am

# Don't fork to become a background process (otherwise pppd will do so
# if a serial device is specified).
#-detach

# Disable IP address negotiation (with this option, the remote IP
# address must be specified with an option on the command line or in an
# options file).
#-ip

# Disable magic number negotiation.  With this option, pppd cannot
# detect a looped-back line.
#-mn

# Disable MRU [Maximum Receive Unit] negotiation (use default, i.e.
# 1500).
#-mru

# Disable protocol field compression negotiation (use default, i.e.
# protocol field compression disabled).
#-pc

# Require the peer to authenticate itself using PAP.
#+pap

# Don't agree to authenticate using PAP.
#-pap

# Require the peer to authenticate itself using CHAP [Cryptographic
# Handshake Authentication Protocol] authentication.
#+chap

# Don't agree to authenticate using CHAP.
#-chap

# Disable negotiation of Van Jacobson style IP header compression (use
# default, i.e. no compression).
#-vj

# Increase debugging level (same as -d).  If this option is given, pppd
# will log the contents of all control packets sent or received in a
# readable form.  The packets are logged through syslog with facility
# daemon and level debug. This information can be directed to a file by
# setting up /etc/syslog.conf appropriately (see syslog.conf(5)).  (If
# pppd is compiled with extra debugging enabled, it will log messages
# using facility local2 instead of daemon).
#debug

# Append the domain name <d> to the local host name for authentication
# purposes.  For example, if gethostname() returns the name porsche,
# but the fully qualified domain name is porsche.Quotron.COM, you would
# use the domain option to set the domain name to Quotron.COM.
#domain <d>

# Enable debugging code in the kernel-level PPP driver.  The argument n
# is a number which is the sum of the following values: 1 to enable
# general debug messages, 2 to request that the contents of received
# packets be printed, and 4 to request that the contents of transmitted
# packets be printed.
#kdebug n

# Set the MTU [Maximum Transmit Unit] value to <n>. Unless the peer
# requests a smaller value via MRU negotiation, pppd will request that
# the kernel networking code send data packets of no more than n bytes
# through the PPP network interface.
#mtu <n>

# Enforce the use of the hostname as the name of the local system for
# authentication purposes (overrides the name option).
#usehostname

# Set the assumed name of the remote system for authentication purposes
# to <n>.
#remotename <n>

# Add an entry to this system's ARP [Address Resolution Protocol]
# table with the IP address of the peer and the Ethernet address of this
# system.
proxyarp

# Use the system password database for authenticating the peer using
# PAP. Note: mgetty already provides this option. If this is specified
# then dialin from users using a script under Linux to fire up ppp wont work.
# login

# If this option is given, pppd will send an LCP echo-request frame to
# the peer every n seconds. Under Linux, the echo-request is sent when
# no packets have been received from the peer for n seconds. Normally
# the peer should respond to the echo-request by sending an echo-reply.
# This option can be used with the lcp-echo-failure option to detect
# that the peer is no longer connected.
lcp-echo-interval 30

# If this option is given, pppd will presume the peer to be dead if n
# LCP echo-requests are sent without receiving a valid LCP echo-reply.
# If this happens, pppd will terminate the connection.  Use of this
# option requires a non-zero value for the lcp-echo-interval parameter.
# This option can be used to enable pppd to terminate after the physical
# connection has been broken (e.g., the modem has hung up) in
# situations where no hardware modem control lines are available.
lcp-echo-failure 4

# Set the LCP restart interval (retransmission timeout) to <n> seconds
# (default 3).
#lcp-restart <n>

# Set the maximum number of LCP terminate-request transmissions to <n>
# (default 3).
#lcp-max-terminate <n>

# Set the maximum number of LCP configure-request transmissions to <n>
# (default 10).
#lcp-max-configure <n>

# Set the maximum number of LCP configure-NAKs returned before starting
# to send configure-Rejects instead to <n> (default 10).
#lcp-max-failure <n>

# Set the IPCP restart interval (retransmission timeout) to <n>
# seconds (default 3).
#ipcp-restart <n>

# Set the maximum number of IPCP terminate-request transmissions to <n>
# (default 3).
#ipcp-max-terminate <n>

# Set the maximum number of IPCP configure-request transmissions to <n>
# (default 10).
#ipcp-max-configure <n>

# Set the maximum number of IPCP configure-NAKs returned before starting
# to send configure-Rejects instead to <n> (default 10).
#ipcp-max-failure <n>

# Set the PAP restart interval (retransmission timeout) to <n> seconds
# (default 3).
#pap-restart <n>

# Set the maximum number of PAP authenticate-request transmissions to
# <n> (default 10).
#pap-max-authreq <n>

# Set the CHAP restart interval (retransmission timeout for
# challenges) to <n> seconds (default 3).
#chap-restart <n>

# Set the maximum number of CHAP challenge transmissions to <n>
# (default 10).
#chap-max-challenge

# If this option is given, pppd will rechallenge the peer every <n>
# seconds.
#chap-interval <n>

# With this option, pppd will accept the peer's idea of our local IP
# address, even if the local IP address was specified in an option.
#ipcp-accept-local

# With this option, pppd will accept the peer's idea of its (remote) IP
# address, even if the remote IP address was specified in an option.
#ipcp-accept-remote