# /etc/ppp/options # # $Id: options,v 1.4 1996/05/01 18:57:04 alvar Exp $ # # Originally created by Jim Knoble # Modified for Debian by alvar Bray # Modified for PPP Server setup by Christoph Lameter # Modified for Slackware by Pat Volkerding # # Use the command egrep -v '#|^ *$' /etc/ppp/options to quickly see what # options are active in this file. # Specify which DNS Servers the incoming Win95 or WinNT Connection should use # Two Servers can be remotely configured # dns-addr 192.168.1.1 # dns-addr 192.168.1.2 # Specify which WINS Servers the incoming connection Win95 or WinNT should use # wins-addr 192.168.1.50 # wins-addr 192.168.1.51 # Run the executable or shell command specified after pppd has # terminated the link. This script could, for example, issue commands # to the modem to cause it to hang up if hardware modem control signals # were not available. #disconnect "chat -- \d+++\d\c OK ath0 OK" # async character map -- 32-bit hex; each bit is a character # that needs to be escaped for pppd to receive it. 0x00000001 # represents '\x01', and 0x80000000 represents '\x1f'. asyncmap 0 # Require the peer to authenticate itself before allowing network # packets to be sent or received. # For a PPP Server with script based logins not using PAP or CHAP # you need to disable this setting. #auth # Do not require the other end of the connection to authenticate itself. # This option is dangerous if pppd is setuid. # If you also have ethernet and are having problems getting PPP to connect # over a modem, try this option. #noauth # Use hardware flow control (i.e. RTS/CTS) to control the flow of data # on the serial port. crtscts # Use software flow control (i.e. XON/XOFF) to control the flow of data # on the serial port. #xonxoff # Specifies that certain characters should be escaped on transmission # (regardless of whether the peer requests them to be escaped with its # async control character map). The characters to be escaped are # specified as a list of hex numbers separated by commas. Note that # almost any character can be specified for the escape option, unlike # the asyncmap option which only allows control characters to be # specified. The characters which may not be escaped are those with hex # values 0x20 - 0x3f or 0x5e. #escape 11,13,ff # Don't use the modem control lines. #local # Specifies that pppd should use a UUCP-style lock on the serial device # to ensure exclusive access to the device. lock # Use the modem control lines. On Ultrix, this option implies hardware # flow control, as for the crtscts option. (This option is not fully # implemented.) modem # Set the MRU [Maximum Receive Unit] value to for negotiation. pppd # will ask the peer to send packets of no more than bytes. The # minimum MRU value is 128. The default MRU value is 1500. A value of # 296 is recommended for slow links (40 bytes for TCP/IP header + 256 # bytes of data). #mru 542 # Set the interface netmask to , a 32 bit netmask in "decimal dot" # notation (e.g. 255.255.255.0). #netmask 255.255.255.0 # Disables the default behaviour when no local IP address is specified, # which is to determine (if possible) the local IP address from the # hostname. With this option, the peer will have to supply the local IP # address during IPCP negotiation (unless it specified explicitly on the # command line or in an options file). #noipdefault # Enables the "passive" option in the LCP. With this option, pppd will # attempt to initiate a connection; if no reply is received from the # peer, pppd will then just wait passively for a valid LCP packet from # the peer (instead of exiting, as it does without this option). #passive # With this option, pppd will not transmit LCP packets to initiate a # connection until a valid LCP packet is received from the peer (as for # the "passive" option with old versions of pppd). #silent # Don't request or allow negotiation of any options for LCP and IPCP # (use default values). #-all # Disable Address/Control compression negotiation (use default, i.e. # address/control field disabled). #-ac # Disable asyncmap negotiation (use the default asyncmap, i.e. escape # all control characters). #-am # Don't fork to become a background process (otherwise pppd will do so # if a serial device is specified). #-detach # Disable IP address negotiation (with this option, the remote IP # address must be specified with an option on the command line or in an # options file). #-ip # Disable magic number negotiation. With this option, pppd cannot # detect a looped-back line. #-mn # Disable MRU [Maximum Receive Unit] negotiation (use default, i.e. # 1500). #-mru # Disable protocol field compression negotiation (use default, i.e. # protocol field compression disabled). #-pc # Require the peer to authenticate itself using PAP. #+pap # Don't agree to authenticate using PAP. #-pap # Require the peer to authenticate itself using CHAP [Cryptographic # Handshake Authentication Protocol] authentication. #+chap # Don't agree to authenticate using CHAP. #-chap # Disable negotiation of Van Jacobson style IP header compression (use # default, i.e. no compression). #-vj # Increase debugging level (same as -d). If this option is given, pppd # will log the contents of all control packets sent or received in a # readable form. The packets are logged through syslog with facility # daemon and level debug. This information can be directed to a file by # setting up /etc/syslog.conf appropriately (see syslog.conf(5)). (If # pppd is compiled with extra debugging enabled, it will log messages # using facility local2 instead of daemon). #debug # Append the domain name to the local host name for authentication # purposes. For example, if gethostname() returns the name porsche, # but the fully qualified domain name is porsche.Quotron.COM, you would # use the domain option to set the domain name to Quotron.COM. #domain # Enable debugging code in the kernel-level PPP driver. The argument n # is a number which is the sum of the following values: 1 to enable # general debug messages, 2 to request that the contents of received # packets be printed, and 4 to request that the contents of transmitted # packets be printed. #kdebug n # Set the MTU [Maximum Transmit Unit] value to . Unless the peer # requests a smaller value via MRU negotiation, pppd will request that # the kernel networking code send data packets of no more than n bytes # through the PPP network interface. #mtu # Enforce the use of the hostname as the name of the local system for # authentication purposes (overrides the name option). #usehostname # Set the assumed name of the remote system for authentication purposes # to . #remotename # Add an entry to this system's ARP [Address Resolution Protocol] # table with the IP address of the peer and the Ethernet address of this # system. proxyarp # Use the system password database for authenticating the peer using # PAP. Note: mgetty already provides this option. If this is specified # then dialin from users using a script under Linux to fire up ppp wont work. # login # If this option is given, pppd will send an LCP echo-request frame to # the peer every n seconds. Under Linux, the echo-request is sent when # no packets have been received from the peer for n seconds. Normally # the peer should respond to the echo-request by sending an echo-reply. # This option can be used with the lcp-echo-failure option to detect # that the peer is no longer connected. lcp-echo-interval 30 # If this option is given, pppd will presume the peer to be dead if n # LCP echo-requests are sent without receiving a valid LCP echo-reply. # If this happens, pppd will terminate the connection. Use of this # option requires a non-zero value for the lcp-echo-interval parameter. # This option can be used to enable pppd to terminate after the physical # connection has been broken (e.g., the modem has hung up) in # situations where no hardware modem control lines are available. lcp-echo-failure 4 # Set the LCP restart interval (retransmission timeout) to seconds # (default 3). #lcp-restart # Set the maximum number of LCP terminate-request transmissions to # (default 3). #lcp-max-terminate # Set the maximum number of LCP configure-request transmissions to # (default 10). #lcp-max-configure # Set the maximum number of LCP configure-NAKs returned before starting # to send configure-Rejects instead to (default 10). #lcp-max-failure # Set the IPCP restart interval (retransmission timeout) to # seconds (default 3). #ipcp-restart # Set the maximum number of IPCP terminate-request transmissions to # (default 3). #ipcp-max-terminate # Set the maximum number of IPCP configure-request transmissions to # (default 10). #ipcp-max-configure # Set the maximum number of IPCP configure-NAKs returned before starting # to send configure-Rejects instead to (default 10). #ipcp-max-failure # Set the PAP restart interval (retransmission timeout) to seconds # (default 3). #pap-restart # Set the maximum number of PAP authenticate-request transmissions to # (default 10). #pap-max-authreq # Set the CHAP restart interval (retransmission timeout for # challenges) to seconds (default 3). #chap-restart # Set the maximum number of CHAP challenge transmissions to # (default 10). #chap-max-challenge # If this option is given, pppd will rechallenge the peer every # seconds. #chap-interval # With this option, pppd will accept the peer's idea of our local IP # address, even if the local IP address was specified in an option. #ipcp-accept-local # With this option, pppd will accept the peer's idea of its (remote) IP # address, even if the remote IP address was specified in an option. #ipcp-accept-remote