diff options
Diffstat (limited to 'source/n/ppp/options.new')
-rw-r--r-- | source/n/ppp/options.new | 276 |
1 files changed, 276 insertions, 0 deletions
diff --git a/source/n/ppp/options.new b/source/n/ppp/options.new new file mode 100644 index 000000000..2a0286576 --- /dev/null +++ b/source/n/ppp/options.new @@ -0,0 +1,276 @@ +# /etc/ppp/options +# +# $Id: options,v 1.4 1996/05/01 18:57:04 alvar Exp $ +# +# Originally created by Jim Knoble <jmknoble@mercury.interpath.net> +# Modified for Debian by alvar Bray <alvar@meiko.co.uk> +# Modified for PPP Server setup by Christoph Lameter <clameter@debian.org> +# Modified for Slackware by Pat Volkerding <volkerdi@slackware.com> +# +# Use the command egrep -v '#|^ *$' /etc/ppp/options to quickly see what +# options are active in this file. + +# Specify which DNS Servers the incoming Win95 or WinNT Connection should use +# Two Servers can be remotely configured +# dns-addr 192.168.1.1 +# dns-addr 192.168.1.2 + +# Specify which WINS Servers the incoming connection Win95 or WinNT should use +# wins-addr 192.168.1.50 +# wins-addr 192.168.1.51 + +# Run the executable or shell command specified after pppd has +# terminated the link. This script could, for example, issue commands +# to the modem to cause it to hang up if hardware modem control signals +# were not available. +#disconnect "chat -- \d+++\d\c OK ath0 OK" + +# async character map -- 32-bit hex; each bit is a character +# that needs to be escaped for pppd to receive it. 0x00000001 +# represents '\x01', and 0x80000000 represents '\x1f'. +asyncmap 0 + +# Require the peer to authenticate itself before allowing network +# packets to be sent or received. +# For a PPP Server with script based logins not using PAP or CHAP +# you need to disable this setting. +#auth + +# Do not require the other end of the connection to authenticate itself. +# This option is dangerous if pppd is setuid. +# If you also have ethernet and are having problems getting PPP to connect +# over a modem, try this option. +#noauth + +# Use hardware flow control (i.e. RTS/CTS) to control the flow of data +# on the serial port. +crtscts + +# Use software flow control (i.e. XON/XOFF) to control the flow of data +# on the serial port. +#xonxoff + +# Specifies that certain characters should be escaped on transmission +# (regardless of whether the peer requests them to be escaped with its +# async control character map). The characters to be escaped are +# specified as a list of hex numbers separated by commas. Note that +# almost any character can be specified for the escape option, unlike +# the asyncmap option which only allows control characters to be +# specified. The characters which may not be escaped are those with hex +# values 0x20 - 0x3f or 0x5e. +#escape 11,13,ff + +# Don't use the modem control lines. +#local + +# Specifies that pppd should use a UUCP-style lock on the serial device +# to ensure exclusive access to the device. +lock + +# Use the modem control lines. On Ultrix, this option implies hardware +# flow control, as for the crtscts option. (This option is not fully +# implemented.) +modem + +# Set the MRU [Maximum Receive Unit] value to <n> for negotiation. pppd +# will ask the peer to send packets of no more than <n> bytes. The +# minimum MRU value is 128. The default MRU value is 1500. A value of +# 296 is recommended for slow links (40 bytes for TCP/IP header + 256 +# bytes of data). +#mru 542 + +# Set the interface netmask to <n>, a 32 bit netmask in "decimal dot" +# notation (e.g. 255.255.255.0). +#netmask 255.255.255.0 + +# Disables the default behaviour when no local IP address is specified, +# which is to determine (if possible) the local IP address from the +# hostname. With this option, the peer will have to supply the local IP +# address during IPCP negotiation (unless it specified explicitly on the +# command line or in an options file). +#noipdefault + +# Enables the "passive" option in the LCP. With this option, pppd will +# attempt to initiate a connection; if no reply is received from the +# peer, pppd will then just wait passively for a valid LCP packet from +# the peer (instead of exiting, as it does without this option). +#passive + +# With this option, pppd will not transmit LCP packets to initiate a +# connection until a valid LCP packet is received from the peer (as for +# the "passive" option with old versions of pppd). +#silent + +# Don't request or allow negotiation of any options for LCP and IPCP +# (use default values). +#-all + +# Disable Address/Control compression negotiation (use default, i.e. +# address/control field disabled). +#-ac + +# Disable asyncmap negotiation (use the default asyncmap, i.e. escape +# all control characters). +#-am + +# Don't fork to become a background process (otherwise pppd will do so +# if a serial device is specified). +#-detach + +# Disable IP address negotiation (with this option, the remote IP +# address must be specified with an option on the command line or in an +# options file). +#-ip + +# Disable magic number negotiation. With this option, pppd cannot +# detect a looped-back line. +#-mn + +# Disable MRU [Maximum Receive Unit] negotiation (use default, i.e. +# 1500). +#-mru + +# Disable protocol field compression negotiation (use default, i.e. +# protocol field compression disabled). +#-pc + +# Require the peer to authenticate itself using PAP. +#+pap + +# Don't agree to authenticate using PAP. +#-pap + +# Require the peer to authenticate itself using CHAP [Cryptographic +# Handshake Authentication Protocol] authentication. +#+chap + +# Don't agree to authenticate using CHAP. +#-chap + +# Disable negotiation of Van Jacobson style IP header compression (use +# default, i.e. no compression). +#-vj + +# Increase debugging level (same as -d). If this option is given, pppd +# will log the contents of all control packets sent or received in a +# readable form. The packets are logged through syslog with facility +# daemon and level debug. This information can be directed to a file by +# setting up /etc/syslog.conf appropriately (see syslog.conf(5)). (If +# pppd is compiled with extra debugging enabled, it will log messages +# using facility local2 instead of daemon). +#debug + +# Append the domain name <d> to the local host name for authentication +# purposes. For example, if gethostname() returns the name porsche, +# but the fully qualified domain name is porsche.Quotron.COM, you would +# use the domain option to set the domain name to Quotron.COM. +#domain <d> + +# Enable debugging code in the kernel-level PPP driver. The argument n +# is a number which is the sum of the following values: 1 to enable +# general debug messages, 2 to request that the contents of received +# packets be printed, and 4 to request that the contents of transmitted +# packets be printed. +#kdebug n + +# Set the MTU [Maximum Transmit Unit] value to <n>. Unless the peer +# requests a smaller value via MRU negotiation, pppd will request that +# the kernel networking code send data packets of no more than n bytes +# through the PPP network interface. +#mtu <n> + +# Enforce the use of the hostname as the name of the local system for +# authentication purposes (overrides the name option). +#usehostname + +# Set the assumed name of the remote system for authentication purposes +# to <n>. +#remotename <n> + +# Add an entry to this system's ARP [Address Resolution Protocol] +# table with the IP address of the peer and the Ethernet address of this +# system. +proxyarp + +# Use the system password database for authenticating the peer using +# PAP. Note: mgetty already provides this option. If this is specified +# then dialin from users using a script under Linux to fire up ppp wont work. +# login + +# If this option is given, pppd will send an LCP echo-request frame to +# the peer every n seconds. Under Linux, the echo-request is sent when +# no packets have been received from the peer for n seconds. Normally +# the peer should respond to the echo-request by sending an echo-reply. +# This option can be used with the lcp-echo-failure option to detect +# that the peer is no longer connected. +lcp-echo-interval 30 + +# If this option is given, pppd will presume the peer to be dead if n +# LCP echo-requests are sent without receiving a valid LCP echo-reply. +# If this happens, pppd will terminate the connection. Use of this +# option requires a non-zero value for the lcp-echo-interval parameter. +# This option can be used to enable pppd to terminate after the physical +# connection has been broken (e.g., the modem has hung up) in +# situations where no hardware modem control lines are available. +lcp-echo-failure 4 + +# Set the LCP restart interval (retransmission timeout) to <n> seconds +# (default 3). +#lcp-restart <n> + +# Set the maximum number of LCP terminate-request transmissions to <n> +# (default 3). +#lcp-max-terminate <n> + +# Set the maximum number of LCP configure-request transmissions to <n> +# (default 10). +#lcp-max-configure <n> + +# Set the maximum number of LCP configure-NAKs returned before starting +# to send configure-Rejects instead to <n> (default 10). +#lcp-max-failure <n> + +# Set the IPCP restart interval (retransmission timeout) to <n> +# seconds (default 3). +#ipcp-restart <n> + +# Set the maximum number of IPCP terminate-request transmissions to <n> +# (default 3). +#ipcp-max-terminate <n> + +# Set the maximum number of IPCP configure-request transmissions to <n> +# (default 10). +#ipcp-max-configure <n> + +# Set the maximum number of IPCP configure-NAKs returned before starting +# to send configure-Rejects instead to <n> (default 10). +#ipcp-max-failure <n> + +# Set the PAP restart interval (retransmission timeout) to <n> seconds +# (default 3). +#pap-restart <n> + +# Set the maximum number of PAP authenticate-request transmissions to +# <n> (default 10). +#pap-max-authreq <n> + +# Set the CHAP restart interval (retransmission timeout for +# challenges) to <n> seconds (default 3). +#chap-restart <n> + +# Set the maximum number of CHAP challenge transmissions to <n> +# (default 10). +#chap-max-challenge + +# If this option is given, pppd will rechallenge the peer every <n> +# seconds. +#chap-interval <n> + +# With this option, pppd will accept the peer's idea of our local IP +# address, even if the local IP address was specified in an option. +#ipcp-accept-local + +# With this option, pppd will accept the peer's idea of its (remote) IP +# address, even if the remote IP address was specified in an option. +#ipcp-accept-remote + |